Search This Blog

Working principle of slow wire processing

 Slow wire walking, also called low-speed wire walking, is a kind of CNC machining machine tool that uses continuously moving fine metal wire as an electrode to pulse spark discharge on the workpiece to generate a high temperature of over 6000 degrees, ablate metal and cut into a workpiece. The principle of wire processing is the phenomenon that there is a gap between the wire electrode and the workpiece, and the metal is removed by continuous discharge. Since the slow-moving wire cutting machine adopts the method of wire electrode continuous feeding, that is, the wire electrode is processed during the movement, so even if the wire electrode is worn out, it can be continuously supplemented, so it can improve the machining accuracy of the parts and slow the wire. The surface roughness of the workpiece processed by the cutting machine can usually reach Ra=0.8μm and above, and the roundness error, linear error and dimensional error of the slow-moving wire cutting machine are much better t

Hydrostatic guideway of CNC machining lathe

The static pressure slide rail (TTW guide) of the CNC machining lathe transfers the oil with a certain pressure through the throttle to the oil cavity between the sliding surfaces of the slide rail (TTW guide) to form a pressure oil film to float the moving parts , Make the sliding rail (TTW guide) surface in a pure liquid friction state.   CNC machining General CNC machining usually refers to computer digital control precision machining, CNC machining lathe, CNC machining milling machine, CNC machining c17200   beryllium   copper   and milling machine, etc. The feed route of finishing is basically carried out along the part contour sequence. Therefore, the focus of determining the feed route is to determine the feed route of rough machining and idle stroke. In the numerical control processing, the control system issues instructions to make the tool perform various motions that meet the requirements, and the shape and size of the workpiece are expressed in the form of numbers and lette

Elimination of Gear Backlash in CNC Machining Feed System

Elimination of Gear Backlash in CNC Machining Feed System   The transmission gear in the feed system of the CNC machining machine tool must eliminate the transmission gap between the meshing gears as much as possible, otherwise the motion will lag behind the command signal after each reversal of the feed system, which will affect the machining accuracy (accuracy) ). There are the following two common methods for CNC machining machine tools to eliminate the transmission gear gap.   1. Rigidity adjustment method   The rigid adjustment method is an adjustment method that cannot be automatically compensated for the tooth side clearance after adjustment. Therefore, the pitch tolerance and tooth thickness of the gear must be strictly controlled, otherwise the flexibility of the transmission will be affected. This adjustment method has a relatively simple structure and a better transmission rigidity.   (1) Eccentric shaft adjustment method   As shown in Figure 610, the gear 1 is mounted on th

Can a Part Machining Plant with CNC Metal Precision Machining Eliminate Your Worries?

keyword:CNC Metal Parts,Precision machine parts,Precision machinery parts processing plant,CNC Turning machining parts manufacturer

CNC metal precision machine parts processing plant can solve your worries?

There are a lot of people working in the big environment, and the influence on the environmental index is not very clear. Because there are too many factors that pollute the environment in reality, you may inadvertently have a little action or behavior that pollutes the environment.

 

CNC Turning machining parts manufacturer by the environment of the main factors are the following:

First, the processing industry will use oil, lubricating oil, cutting fluid and a little oily liquid, must dispose of the waste oil, to avoid environmental damage;

Two, the lathe inside of the iron filings must be cleaned, stored in the designated area, do not throw at will, to avoid accidental injury;

Three, clean the worktable at any time, the processing parts will cause a little oil or residue to the operating table, if not clean, will also affect the operator's mood;

Four, processing materials must ensure that it is environmentally friendly materials, otherwise it will cause a large area of environmental pollution.

More than likely you will meet at four o 'clock this, chances are you will avoid, however, must be careful, otherwise, not affect others, of course, if the CNC Turning machining parts manufacturer to be able to avoid all these factors, which affect the environment, so their influence is also will improve, not only does this not influence in the near,May also let you in the industry are prominent encirclements, completely stable figure, this is the strength of the environment to cultivate businesses.

Now will be speed, some processing plants in order to be able to quickly make customers' products, will think a little crash method, thereby reducing the applicability and quality of products, this is a major drawback of processing plants.To be able to make products that exceed customer satisfaction within a limited time is to be qualified. On the contrary, it is to fail, and the consequence of failure is to reduce customer satisfaction with you.If there is accidental damage in transportation, then, the consequences must be grasped, can not directly call the customer responsible, because the customer believes you will choose you, can not go to the customer when there is a problem, this is the wrong approach.Be sure to avoid this mistake.

Yi Jin Hardware Recommendation:cnc-milling-parts

If you are interested in our products, you are welcome to send your requirements with your drawings to us via email. We are very glad to give you the most favorable quotation. If so, our email is: [email protected],Click on the email address on the left to send us an email quickly and easily

Link to this article:Can a Part Machining Plant with CNC Metal Precision Machining Eliminate Your Worries?

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.:Cnc Machining,Thank

Contact Us


Get In Touch or Get A Quote

Need an expert? you are more than welcomed to
leave your contact info and we will be in touch shortly
YOUR COMPANY
Sifangyuan Industrial Park, Xinshapu, Huaide Community
Humen town, Dongguan City, Guangdong Province. 
860769-82886112
860769-82886112