Search This Blog

Working principle of slow wire processing

 Slow wire walking, also called low-speed wire walking, is a kind of CNC machining machine tool that uses continuously moving fine metal wire as an electrode to pulse spark discharge on the workpiece to generate a high temperature of over 6000 degrees, ablate metal and cut into a workpiece. The principle of wire processing is the phenomenon that there is a gap between the wire electrode and the workpiece, and the metal is removed by continuous discharge. Since the slow-moving wire cutting machine adopts the method of wire electrode continuous feeding, that is, the wire electrode is processed during the movement, so even if the wire electrode is worn out, it can be continuously supplemented, so it can improve the machining accuracy of the parts and slow the wire. The surface roughness of the workpiece processed by the cutting machine can usually reach Ra=0.8μm and above, and the roundness error, linear error and dimensional error of the slow-moving wire cutting machine are much bett...

What are the rules for metal stamping die scrap tube?

The Purpose Standardize the management of the scrapping of the company's metal stamping dies, prevent the loss of company assets, and formulate this system specially. Scope of application It is suitable for the management of the company's scrap molds. Definition If the molds listed in the assets of the company fall under one of the following circumstances, the use management department may apply for scrapping. 1. Molds that exceed the specified service life. 2. The mold is severely damaged by accidents or accidents, and molds that cannot be repaired or have no repair value. 3. Metal stamping dies that have not reached the service life, but due to safety, quality, efficiency and other issues, the repair still fails to meet the minimum requirements of the customer's product process or affects the production safety and efficiency. 4. Product customers have stopped placing orders or have not placed orders for molds in several years. 4. Responsibilities 1. Responsibilities of th...

Introduction of KOVAR parts

KOVAR parts are commonly used as metal casing materials in the electronic packaging industry. Because they have a linear expansion coefficient close to that of molybdenum group glass, and can produce less sealing stress during the sealing (melting) process with molybdenum group glass, so To obtain good air-tightness, in order to make the metal tube and shell to achieve air-tight sealing, in the entire sealing process, the annealing process undoubtedly plays an important role as a link between the previous and the next. The internal stress generated during KOVAR  machining also prepares the material structure for the implementation of the subsequent process-the sealing process of the metal parts. The main purpose of annealing Kovar shell before sealing is to: (1) Eliminate machining stress. When Kovar undergoes plastic machining deformation during cold working, about 10% to 15% of the applied energy is converted into internal energy, which is commonly referred to as internal stre...

Six points of attention to auto tire self-inspection

As the "foot" of a car, tires usually serve the host silently. However, it is such a critical part that *is easy to be "outsided" by others. Today we will teach you a few precautions for self-inspection of tires.
pierce the hole:
Have your car tires been punctured? If so, how long ago was it? In fact, for a car that has been repaired, even if it is no problem to use it temporarily, its endurance under extreme load will be much lower than before. In addition, if there are more than 3 holes in the same tire, it is recommended that you replace the tire as soon as possible.
drum kit:
When a car drives through pits, obstacles and road edges at high speeds, the tires locally will be severely deformed under the huge impact force, and the internal pressure will increase instantaneously. The direct consequence of this is that the tires will bulge.The tires that have been bulged must be replaced immediately, otherwise there is a risk of a tire blowout.
pattern:
Generally speaking, the tires of a family car in normal use can be replaced every 60,000 kilometers or two years, but tires with severe pattern wear should be replaced early. Nowadays, repair shops have pattern wear scales, and car owners can buy one to check the pattern wear of their tires at any time. In addition, increased tread cracks are also a sign of serious tire aging. Usually, car owners can properly spray some tire protection wax, and try not to press corrosive liquids when driving.
Air pressure:
For a front-wheel drive vehicle, the front wheels sometimes look a little flat because the engine, gearbox and other important drive components are pressed on the front. The visual inspection is inaccurate, you must use a dedicated tire pressure gauge to measure whether the tire pressure is normal.
石子:
Some car owners often hear that their car makes noises when driving, but there is no malfunction when driving. At this time, you should check if there are any small stones stuck in the tire pattern. In fact, it can be solved by taking the time to dig out these small stones in the tread pattern with the key.
Spare tire:
If you want the spare tire to play a real emergency role, you should also pay attention to its maintenance at ordinary times. First of all, check the pressure of the spare tire frequently; secondly, pay attention to the prevention of oil corrosion on the spare tire. The tire is made of rubber, so you are afraid of being corroded by various oils. The tires will bulge and corrode soon after being stained with oil, which will greatly reduce the service life of the tires; *After that, the life of the spare tire is about 4 years. Many car owners mistakenly believe that the spare tire is always new if it is not used, but it is actually over. Even if the spare tire has not been used once in 4 years, it needs to be replaced, otherwise the spare tire will become a waste tire.

Link to this article:Six points of attention to auto tire self-inspection

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.:Cnc Machining,Thank

Contact Us


Get In Touch or Get A Quote

Need an expert? you are more than welcomed to
leave your contact info and we will be in touch shortly
YOUR COMPANY
Sifangyuan Industrial Park, Xinshapu, Huaide Community
Humen town, Dongguan City, Guangdong Province. 
860769-82886112
860769-82886112