Search This Blog

Working principle of slow wire processing

 Slow wire walking, also called low-speed wire walking, is a kind of CNC machining machine tool that uses continuously moving fine metal wire as an electrode to pulse spark discharge on the workpiece to generate a high temperature of over 6000 degrees, ablate metal and cut into a workpiece. The principle of wire processing is the phenomenon that there is a gap between the wire electrode and the workpiece, and the metal is removed by continuous discharge. Since the slow-moving wire cutting machine adopts the method of wire electrode continuous feeding, that is, the wire electrode is processed during the movement, so even if the wire electrode is worn out, it can be continuously supplemented, so it can improve the machining accuracy of the parts and slow the wire. The surface roughness of the workpiece processed by the cutting machine can usually reach Ra=0.8μm and above, and the roundness error, linear error and dimensional error of the slow-moving wire cutting machine are much better t

Hydrostatic guideway of CNC machining lathe

The static pressure slide rail (TTW guide) of the CNC machining lathe transfers the oil with a certain pressure through the throttle to the oil cavity between the sliding surfaces of the slide rail (TTW guide) to form a pressure oil film to float the moving parts , Make the sliding rail (TTW guide) surface in a pure liquid friction state.   CNC machining General CNC machining usually refers to computer digital control precision machining, CNC machining lathe, CNC machining milling machine, CNC machining c17200   beryllium   copper   and milling machine, etc. The feed route of finishing is basically carried out along the part contour sequence. Therefore, the focus of determining the feed route is to determine the feed route of rough machining and idle stroke. In the numerical control processing, the control system issues instructions to make the tool perform various motions that meet the requirements, and the shape and size of the workpiece are expressed in the form of numbers and lette

Elimination of Gear Backlash in CNC Machining Feed System

Elimination of Gear Backlash in CNC Machining Feed System   The transmission gear in the feed system of the CNC machining machine tool must eliminate the transmission gap between the meshing gears as much as possible, otherwise the motion will lag behind the command signal after each reversal of the feed system, which will affect the machining accuracy (accuracy) ). There are the following two common methods for CNC machining machine tools to eliminate the transmission gear gap.   1. Rigidity adjustment method   The rigid adjustment method is an adjustment method that cannot be automatically compensated for the tooth side clearance after adjustment. Therefore, the pitch tolerance and tooth thickness of the gear must be strictly controlled, otherwise the flexibility of the transmission will be affected. This adjustment method has a relatively simple structure and a better transmission rigidity.   (1) Eccentric shaft adjustment method   As shown in Figure 610, the gear 1 is mounted on th

What’s the difference between screw, bolt and nut?

(1) bolt:

A type of fastener consisting of a head and a screw (cylindrical body with external thread) to be fitted with a nut for fastening two parts with through holes.This type of connection is called the bolt connection. If the nut is unscrewed from the bolt, it can also make the two parts separate, so the bolt connection is a detachable connection.

(2) screws:

A kind of fastener composed of head and screw can be divided into three types according to their uses — machine screws, setting screws and screws for special purposes.Machine screws are mainly used for fastening connection between a part with an internal threaded hole and a part with a through hole, without nut matching (this connection form is called screw connection, also a detachable connection;It can also be used with a nut for fastening connection between two parts with through holes.Set screws are mainly used to fix the relative position between two parts.Special purpose screws are ring screws for lifting parts.

The best material is 316 corrosion resistant stainless steel, followed by 304.Carbon steel is the next most common material.

The standard of hexagon nut and utility have what

As a standard part, nuts and rivets with pull mandrel have their own standards.Xiaobian on the hexagon nut standard is summarized for the difference and connection and their use.

For hexagon nuts, the commonly used standards are:

GB41 Ⅰ Hexagon nuts — Class C

GB6170 Ⅰ type hexagon nut — A, B grade

GB6171Ⅰ Hexagon nuts — fine tooth — grade A and B

GB6172 Hexagon thin nuts — Class A and B — Chamfered

GB6173 Hexagon thin nuts — fine tooth — grade A and B

GB6174 Hexagon thin nuts — Class B — No chamfering

GB6175Ⅱ type hexagon nut — A, B grade

GB6176Ⅱ type hexagon nuts — fine tooth — grade A and B

GB6177 Hexagon flange nuts — Class A

GB55 hexagon thick nut

GB56 hexagon ultra thick nut

GB1229 Hexagon nuts (high strength for steel structures)

1, ordinary hexagon nuts: widely used, characterized by large fastening force, the disadvantage is that there should be enough operating space in the installation, the installation can use a live wrench, open wrench or glasses wrench, the wrench above all need a lot of operating space.

2, cylinder head hex nut, is the most widely used in all the screws, because its binding force is larger, can use Allen key operation, the installation is very convenient, when used in almost all kinds of structure, more beautiful and tidy appearance, defect is slightly lower than outside hexagonal fastening force, also repeated use can't remove the socket head broken easily.

3, disk head hexagon nut: rarely used in machinery, mechanical properties of the same, mostly used in furniture, the main role is to increase the contact surface with wooden materials and increase the appearance of the ornamental.

4, headless hexagon nut: some structures must be used, such as the need for a large jacking force of the top wire structure, or the need to hide the place of the cylindrical head.

5, countersunk hex socket nut: mostly used in power machinery, the main role of the same hex socket.

6. Nylon lock nut: it is inlaid with nylon apron in hexagonal face to prevent loosening of thread. It is used in strong power machinery.

7, flange nut: mainly play a role in increasing the contact surface with the workpiece, mostly used in pipes, fasteners and some stamping and casting parts.

Link to this article:What's the difference between screw, bolt and nut?

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.:Cnc Machining,Thank

Contact Us


Get In Touch or Get A Quote

Need an expert? you are more than welcomed to
leave your contact info and we will be in touch shortly
YOUR COMPANY
Sifangyuan Industrial Park, Xinshapu, Huaide Community
Humen town, Dongguan City, Guangdong Province. 
860769-82886112
860769-82886112