Search This Blog

Working principle of slow wire processing

 Slow wire walking, also called low-speed wire walking, is a kind of CNC machining machine tool that uses continuously moving fine metal wire as an electrode to pulse spark discharge on the workpiece to generate a high temperature of over 6000 degrees, ablate metal and cut into a workpiece. The principle of wire processing is the phenomenon that there is a gap between the wire electrode and the workpiece, and the metal is removed by continuous discharge. Since the slow-moving wire cutting machine adopts the method of wire electrode continuous feeding, that is, the wire electrode is processed during the movement, so even if the wire electrode is worn out, it can be continuously supplemented, so it can improve the machining accuracy of the parts and slow the wire. The surface roughness of the workpiece processed by the cutting machine can usually reach Ra=0.8μm and above, and the roundness error, linear error and dimensional error of the slow-moving wire cutting machine are much better t

Hydrostatic guideway of CNC machining lathe

The static pressure slide rail (TTW guide) of the CNC machining lathe transfers the oil with a certain pressure through the throttle to the oil cavity between the sliding surfaces of the slide rail (TTW guide) to form a pressure oil film to float the moving parts , Make the sliding rail (TTW guide) surface in a pure liquid friction state.   CNC machining General CNC machining usually refers to computer digital control precision machining, CNC machining lathe, CNC machining milling machine, CNC machining c17200   beryllium   copper   and milling machine, etc. The feed route of finishing is basically carried out along the part contour sequence. Therefore, the focus of determining the feed route is to determine the feed route of rough machining and idle stroke. In the numerical control processing, the control system issues instructions to make the tool perform various motions that meet the requirements, and the shape and size of the workpiece are expressed in the form of numbers and lette

Elimination of Gear Backlash in CNC Machining Feed System

Elimination of Gear Backlash in CNC Machining Feed System   The transmission gear in the feed system of the CNC machining machine tool must eliminate the transmission gap between the meshing gears as much as possible, otherwise the motion will lag behind the command signal after each reversal of the feed system, which will affect the machining accuracy (accuracy) ). There are the following two common methods for CNC machining machine tools to eliminate the transmission gear gap.   1. Rigidity adjustment method   The rigid adjustment method is an adjustment method that cannot be automatically compensated for the tooth side clearance after adjustment. Therefore, the pitch tolerance and tooth thickness of the gear must be strictly controlled, otherwise the flexibility of the transmission will be affected. This adjustment method has a relatively simple structure and a better transmission rigidity.   (1) Eccentric shaft adjustment method   As shown in Figure 610, the gear 1 is mounted on th

How can lithium batteries enter the light electric vehicle market

How can lithium batteries enter the light electric vehicle market? The following measures can be considered. **, give full play to the characteristics of lithium batteries, design light electric vehicles with higher performance. For example, install batteries of the same quality to increase the capacity of the car (driving range, climbing ability, load capacity with a single charge). Second, design light electric vehicles with 1, 2, 3, and 4 people. Third, study to improve the quality of the car and reduce the standard. Fourth, strengthen sales measures to enable it to enter the countryside and go abroad. Fifth, let lithium battery electric vehicles enter the market as soon as possible and withstand the exercise of the market.

Statistics on the number of electric bicycles in China from 1998 to 2005 * The battery field also supported and promoted the development of electronic devices. Now, light-duty electric vehicles have been widely accepted, and lead-acid batteries have played a big role. In the past 7 years, the production and sales volume has nearly doubled every year. Lead-acid batteries have occupied the position of light electric vehicles at this stage with their mature technology and lower prices.

In this period, the research work of lithium-ion batteries must be continuously strengthened. In addition to improving the performance of lithium manganate and reducing its price, it is also necessary to study new battery materials and find new materials with larger capacity, longer life, and lower cost.

The    co-precipitation method is the best preparation method. The catalyst prepared by the combination of sodium hydroxide and urea precipitation has higher activity and thermal stability. The research results of using NHO to filter out the copper component in the catalyst show that the copper content in the catalyst has a best value, and Cu plays an important role in the formation of active sites of the catalyst. For automotive parts and parts machining, PTJ Shop offers the highest degree of OEM service with a basis of 10+ years experience serving the automotive industry. Our automotive precision shop and experts deliver confidence. We have perfected the art of producing large component volumes with complete JIT reliability, backed by the quality and long-term reliability our customers expect.

Link to this article:How can lithium batteries enter the light electric vehicle market

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.:Cnc Machining,Thank

Contact Us


Get In Touch or Get A Quote

Need an expert? you are more than welcomed to
leave your contact info and we will be in touch shortly
YOUR COMPANY
Sifangyuan Industrial Park, Xinshapu, Huaide Community
Humen town, Dongguan City, Guangdong Province. 
860769-82886112
860769-82886112