Search This Blog

Working principle of slow wire processing

 Slow wire walking, also called low-speed wire walking, is a kind of CNC machining machine tool that uses continuously moving fine metal wire as an electrode to pulse spark discharge on the workpiece to generate a high temperature of over 6000 degrees, ablate metal and cut into a workpiece. The principle of wire processing is the phenomenon that there is a gap between the wire electrode and the workpiece, and the metal is removed by continuous discharge. Since the slow-moving wire cutting machine adopts the method of wire electrode continuous feeding, that is, the wire electrode is processed during the movement, so even if the wire electrode is worn out, it can be continuously supplemented, so it can improve the machining accuracy of the parts and slow the wire. The surface roughness of the workpiece processed by the cutting machine can usually reach Ra=0.8μm and above, and the roundness error, linear error and dimensional error of the slow-moving wire cutting machine are much better t

Hydrostatic guideway of CNC machining lathe

The static pressure slide rail (TTW guide) of the CNC machining lathe transfers the oil with a certain pressure through the throttle to the oil cavity between the sliding surfaces of the slide rail (TTW guide) to form a pressure oil film to float the moving parts , Make the sliding rail (TTW guide) surface in a pure liquid friction state.   CNC machining General CNC machining usually refers to computer digital control precision machining, CNC machining lathe, CNC machining milling machine, CNC machining c17200   beryllium   copper   and milling machine, etc. The feed route of finishing is basically carried out along the part contour sequence. Therefore, the focus of determining the feed route is to determine the feed route of rough machining and idle stroke. In the numerical control processing, the control system issues instructions to make the tool perform various motions that meet the requirements, and the shape and size of the workpiece are expressed in the form of numbers and lette

Elimination of Gear Backlash in CNC Machining Feed System

Elimination of Gear Backlash in CNC Machining Feed System   The transmission gear in the feed system of the CNC machining machine tool must eliminate the transmission gap between the meshing gears as much as possible, otherwise the motion will lag behind the command signal after each reversal of the feed system, which will affect the machining accuracy (accuracy) ). There are the following two common methods for CNC machining machine tools to eliminate the transmission gear gap.   1. Rigidity adjustment method   The rigid adjustment method is an adjustment method that cannot be automatically compensated for the tooth side clearance after adjustment. Therefore, the pitch tolerance and tooth thickness of the gear must be strictly controlled, otherwise the flexibility of the transmission will be affected. This adjustment method has a relatively simple structure and a better transmission rigidity.   (1) Eccentric shaft adjustment method   As shown in Figure 610, the gear 1 is mounted on th

Mitsubishi AA084VC05

Mitsubishi AA084VC05
#AA084VC05 Mitsubishi AA084VC05 New AA084VC05 Mitsubishi 8.4 inch LCM 640×480 500:1 262K CCFL TTL, AA084VC05 pictures, AA084VC05 price, #AA084VC05 supplier
-------------------------------------------------------------------
Email: [email protected]

-------------------------------------------------------------------
Brand: Mitsubishi
Model: AA084VC05 
Diagonal Size: 8.4 inch  Type:  a-Si TFT-LCD, LCM 
Pixel Format:  640(RGB)×480   [VGA] 
Configuration RGB Vertical Stripe
Active Area:  170.88(H)×128.16(V) mm 
Outline Dim. 199.5(H)×149(V) ×12(D) mm
Bezel Area:  174.9(H)×132.2(V) mm 
Treatment: Antiglare, Hard coating (3H)
Luminance:  480 cd/m² (Typ.) 
Contrast Ratio 500:1 (Typ.) (TM)    
View Direction: 6 o'clock   
Response Time: 6/19 (Typ.)(Tr/Td)
Viewing Angle:  65/65/50/60 (Typ.)(CR≥10) Left / Right / Up / Down 
Operating Mode TN, Normally White, 
Support Color: 262K   
Light Source: CCFL  [2 pcs] , 50K hours , W/O Driver
Weight 360g (Typ.)
Designed For Industrial Application
Frame Rate 60Hz 
Touch PanelWithout
Interface Type 31 pins   
CMOS (1 ch, 6-bit) , Connector
Power Supply3.3V (Typ.) 
Environment Operating Temperature: -20 ~ 70 °C ; Storage Temperature: -20 ~ 80 °C
AA084VC05 inverter, AA084VC05 power supply, AA084VC05 electronic board, AA084VC05 VGA board, AA084VC05 touchscreen available.

Contact Us


Get In Touch or Get A Quote

Need an expert? you are more than welcomed to
leave your contact info and we will be in touch shortly
YOUR COMPANY
Sifangyuan Industrial Park, Xinshapu, Huaide Community
Humen town, Dongguan City, Guangdong Province. 
860769-82886112
860769-82886112