Search This Blog

Working principle of slow wire processing

 Slow wire walking, also called low-speed wire walking, is a kind of CNC machining machine tool that uses continuously moving fine metal wire as an electrode to pulse spark discharge on the workpiece to generate a high temperature of over 6000 degrees, ablate metal and cut into a workpiece. The principle of wire processing is the phenomenon that there is a gap between the wire electrode and the workpiece, and the metal is removed by continuous discharge. Since the slow-moving wire cutting machine adopts the method of wire electrode continuous feeding, that is, the wire electrode is processed during the movement, so even if the wire electrode is worn out, it can be continuously supplemented, so it can improve the machining accuracy of the parts and slow the wire. The surface roughness of the workpiece processed by the cutting machine can usually reach Ra=0.8μm and above, and the roundness error, linear error and dimensional error of the slow-moving wire cutting machine are much better t

Hydrostatic guideway of CNC machining lathe

The static pressure slide rail (TTW guide) of the CNC machining lathe transfers the oil with a certain pressure through the throttle to the oil cavity between the sliding surfaces of the slide rail (TTW guide) to form a pressure oil film to float the moving parts , Make the sliding rail (TTW guide) surface in a pure liquid friction state.   CNC machining General CNC machining usually refers to computer digital control precision machining, CNC machining lathe, CNC machining milling machine, CNC machining c17200   beryllium   copper   and milling machine, etc. The feed route of finishing is basically carried out along the part contour sequence. Therefore, the focus of determining the feed route is to determine the feed route of rough machining and idle stroke. In the numerical control processing, the control system issues instructions to make the tool perform various motions that meet the requirements, and the shape and size of the workpiece are expressed in the form of numbers and lette

Elimination of Gear Backlash in CNC Machining Feed System

Elimination of Gear Backlash in CNC Machining Feed System   The transmission gear in the feed system of the CNC machining machine tool must eliminate the transmission gap between the meshing gears as much as possible, otherwise the motion will lag behind the command signal after each reversal of the feed system, which will affect the machining accuracy (accuracy) ). There are the following two common methods for CNC machining machine tools to eliminate the transmission gear gap.   1. Rigidity adjustment method   The rigid adjustment method is an adjustment method that cannot be automatically compensated for the tooth side clearance after adjustment. Therefore, the pitch tolerance and tooth thickness of the gear must be strictly controlled, otherwise the flexibility of the transmission will be affected. This adjustment method has a relatively simple structure and a better transmission rigidity.   (1) Eccentric shaft adjustment method   As shown in Figure 610, the gear 1 is mounted on th

TIANMA TM043NDH02

TIANMA TM043NDH02
#TM043NDH02 TIANMA TM043NDH02 New , TM043NDH02 pictures, TM043NDH02 price, #TM043NDH02 supplier
-------------------------------------------------------------------
Email: sales@shunlongwei.com

-------------------------------------------------------------------
Panel Brand: TIANMA
Panel Model: TM043NDH02
Panel Size: 4.3"
Panel Type: a-Si TFT-LCD, LCM
Resolution: 480(RGB)×272 , WQVGA
Pixel Format: RGB Vertical Stripe
Display Area: 95.04(W)×53.856(H) mm
Bezel Opening: 99.6(W)×56.7(H) mm
Outline Size: 105.5(W)×67.2(H) ×3.2(D) mm
Surface: Antiglare, Hard coating (3H)
Brightness: 300 cd/m² (Typ.)
Contrast Ratio: 500:1 (Typ.) (TM)    
Viewing Angle: 70/70/70/50 (Typ.)(CR≥10) Left / Right / Up / Down
Display Mode: TN, Normally White, Transmissive
Best View on: 6 o'clock
Response Time: 20 (Typ.)(Tr+Td)
Display Colors: 16.7M   50% NTSC
Lamp Type: 5S2P WLED , 20K hours , Without Driver
Frequency: 60Hz
Touch Screen: Without
Panel WeightL:  44.1g
Application: Portable Navigation  MP3 PMP
Signal Interface: Parallel RGB (1 ch, 8-bit) , 40 pins , FPC
Input Voltage: 3.3V (Typ.)
Environment: Operating Temp.: -20 ~ 70 °C ; Storage Temp.: -30 ~ 80 °C
TM043NDH02 inverter, TM043NDH02 power supply, TM043NDH02 electronic board, TM043NDH02 VGA board, TM043NDH02 touchscreen available.

Contact Us


Get In Touch or Get A Quote

Need an expert? you are more than welcomed to
leave your contact info and we will be in touch shortly
YOUR COMPANY
Sifangyuan Industrial Park, Xinshapu, Huaide Community
Humen town, Dongguan City, Guangdong Province. 
860769-82886112
860769-82886112