Search This Blog

Working principle of slow wire processing

 Slow wire walking, also called low-speed wire walking, is a kind of CNC machining machine tool that uses continuously moving fine metal wire as an electrode to pulse spark discharge on the workpiece to generate a high temperature of over 6000 degrees, ablate metal and cut into a workpiece. The principle of wire processing is the phenomenon that there is a gap between the wire electrode and the workpiece, and the metal is removed by continuous discharge. Since the slow-moving wire cutting machine adopts the method of wire electrode continuous feeding, that is, the wire electrode is processed during the movement, so even if the wire electrode is worn out, it can be continuously supplemented, so it can improve the machining accuracy of the parts and slow the wire. The surface roughness of the workpiece processed by the cutting machine can usually reach Ra=0.8μm and above, and the roundness error, linear error and dimensional error of the slow-moving wire cutting machine are much better t

Hydrostatic guideway of CNC machining lathe

The static pressure slide rail (TTW guide) of the CNC machining lathe transfers the oil with a certain pressure through the throttle to the oil cavity between the sliding surfaces of the slide rail (TTW guide) to form a pressure oil film to float the moving parts , Make the sliding rail (TTW guide) surface in a pure liquid friction state.   CNC machining General CNC machining usually refers to computer digital control precision machining, CNC machining lathe, CNC machining milling machine, CNC machining c17200   beryllium   copper   and milling machine, etc. The feed route of finishing is basically carried out along the part contour sequence. Therefore, the focus of determining the feed route is to determine the feed route of rough machining and idle stroke. In the numerical control processing, the control system issues instructions to make the tool perform various motions that meet the requirements, and the shape and size of the workpiece are expressed in the form of numbers and lette

Elimination of Gear Backlash in CNC Machining Feed System

Elimination of Gear Backlash in CNC Machining Feed System   The transmission gear in the feed system of the CNC machining machine tool must eliminate the transmission gap between the meshing gears as much as possible, otherwise the motion will lag behind the command signal after each reversal of the feed system, which will affect the machining accuracy (accuracy) ). There are the following two common methods for CNC machining machine tools to eliminate the transmission gear gap.   1. Rigidity adjustment method   The rigid adjustment method is an adjustment method that cannot be automatically compensated for the tooth side clearance after adjustment. Therefore, the pitch tolerance and tooth thickness of the gear must be strictly controlled, otherwise the flexibility of the transmission will be affected. This adjustment method has a relatively simple structure and a better transmission rigidity.   (1) Eccentric shaft adjustment method   As shown in Figure 610, the gear 1 is mounted on th

AUO G156XW01 V1

AUO G156XW01 V1
#G156XW01 V1 AUO G156XW01 V1 New G156XW01 V1 AUO 15.6 inch LCM 1366×768 400 500:1 85/85/80/80 16.2M WLED LVDS, G156XW01 V1 pictures, G156XW01 V1 price, #G156XW01 V1 supplier
-------------------------------------------------------------------
Email: sales@shunlongwei.com

-------------------------------------------------------------------
Manufacturer AUO
Model Name G156XW01 V1  
Screen Size 15.6 inch
Screen Type LCM ,   a-Si TFT-LCD
Pixel Number 1366(RGB)×768   (WXGA)  100PPI
Arrangement RGB Vertical Stripe
Active Area(mm) 344.232 × 193.536 (H×V)
Outline(mm) 363.8 × 215.9 × 17.35 (H×V×D)
Bezel Area(mm) 347.54 × 196.83 (H×V)
Treatment Antiglare, Hard coating (3H)
Luminance 400 (Typ.)(cd/m²)
Contrast Ratio 500 : 1 (Typ.) (TM)    
Viewing Angle 85/85/80/80 (Typ.)(CR≥10)
Work Mode TN, Normally White, Transmissive 
Good View at - Response 6/2 (Typ.)(Tr/Td) ms
Color Depth 16.2M   70% NTSC
Backlight WLED , 50K hours , With LED Driver
Mass 1.25/1.35Kgs (Typ./Max.)
Refresh Rate 60Hz 
Touchscreen Without
Signal Type LVDS (1 ch, 8-bit) , 30 pins Connector
Voltage Supply 5.0V (Typ.) 
Max. Ratings Storage Temp.: -20 ~ 60 °C    Operating Temp.: 0 ~ 60 °C   

G156XW01 V1 inverter, G156XW01 V1 power supply, G156XW01 V1 electronic board, G156XW01 V1 VGA board, G156XW01 V1 touchscreen available.

Contact Us


Get In Touch or Get A Quote

Need an expert? you are more than welcomed to
leave your contact info and we will be in touch shortly
YOUR COMPANY
Sifangyuan Industrial Park, Xinshapu, Huaide Community
Humen town, Dongguan City, Guangdong Province. 
860769-82886112
860769-82886112