Search This Blog

Working principle of slow wire processing

 Slow wire walking, also called low-speed wire walking, is a kind of CNC machining machine tool that uses continuously moving fine metal wire as an electrode to pulse spark discharge on the workpiece to generate a high temperature of over 6000 degrees, ablate metal and cut into a workpiece. The principle of wire processing is the phenomenon that there is a gap between the wire electrode and the workpiece, and the metal is removed by continuous discharge. Since the slow-moving wire cutting machine adopts the method of wire electrode continuous feeding, that is, the wire electrode is processed during the movement, so even if the wire electrode is worn out, it can be continuously supplemented, so it can improve the machining accuracy of the parts and slow the wire. The surface roughness of the workpiece processed by the cutting machine can usually reach Ra=0.8μm and above, and the roundness error, linear error and dimensional error of the slow-moving wire cutting machine are much better t

Hydrostatic guideway of CNC machining lathe

The static pressure slide rail (TTW guide) of the CNC machining lathe transfers the oil with a certain pressure through the throttle to the oil cavity between the sliding surfaces of the slide rail (TTW guide) to form a pressure oil film to float the moving parts , Make the sliding rail (TTW guide) surface in a pure liquid friction state.   CNC machining General CNC machining usually refers to computer digital control precision machining, CNC machining lathe, CNC machining milling machine, CNC machining c17200   beryllium   copper   and milling machine, etc. The feed route of finishing is basically carried out along the part contour sequence. Therefore, the focus of determining the feed route is to determine the feed route of rough machining and idle stroke. In the numerical control processing, the control system issues instructions to make the tool perform various motions that meet the requirements, and the shape and size of the workpiece are expressed in the form of numbers and lette

Elimination of Gear Backlash in CNC Machining Feed System

Elimination of Gear Backlash in CNC Machining Feed System   The transmission gear in the feed system of the CNC machining machine tool must eliminate the transmission gap between the meshing gears as much as possible, otherwise the motion will lag behind the command signal after each reversal of the feed system, which will affect the machining accuracy (accuracy) ). There are the following two common methods for CNC machining machine tools to eliminate the transmission gear gap.   1. Rigidity adjustment method   The rigid adjustment method is an adjustment method that cannot be automatically compensated for the tooth side clearance after adjustment. Therefore, the pitch tolerance and tooth thickness of the gear must be strictly controlled, otherwise the flexibility of the transmission will be affected. This adjustment method has a relatively simple structure and a better transmission rigidity.   (1) Eccentric shaft adjustment method   As shown in Figure 610, the gear 1 is mounted on th

CNC turning and milling composite processing manufacturers explain the selection of lathes


1. Preparation

 

The CNC turning and milling composite processing manufacturer introduced the process requirements of typical parts and the batch of processed workpieces. The function that the CNC lathe should have is to make preparations and the prerequisites for the reasonable selection of CNC lathes. Meet the process requirements of typical parts

 

The process requirements of typical parts are mainly the structural size, processing range and accuracy requirements of the parts. According to the accuracy requirements, that is, the dimensional accuracy, positioning accuracy and surface roughness of the workpiece, the control accuracy of the CNC lathe is selected.

 

Choose based on reliability. Reliability is a guarantee for improving product quality and production efficiency. The reliability of a CNC machine tool means that the machine tool runs stably for a long time without failure when it performs its functions under specified conditions. That is, the mean time between failures is long, even if there is a failure, it can be restored in a short time and put into use again. Choose machine tools with reasonable structure, well-manufactured, and mass-produced machines. Generally, the more users, the higher the reliability of the CNC system.

 

2. Purchase of machine tool accessories and tools

 

According to the analysis of CNC turning-milling composite processing manufacturers, the machine tool accessories, spare parts and their supply capacity, and cutting tools are very important to the CNC machining and turning centers that have been put into production. When choosing a machine tool, carefully consider the compatibility of tools and accessories.

 

3. Focus on the identity of the control system

 Manufacturers generally choose products from the same manufacturer, and should at least purchase control systems from the same manufacturer, which brings great convenience to the maintenance work. Teaching units require students to be knowledgeable and knowledgeable, so it is a wise choice to choose different systems and equip them with various simulation software.

 

4. Choose according to the performance-price ratio

 Introduced by CNC turning-milling composite machining manufacturers, to ensure that the functions and accuracy are not idle, not wasted, and do not choose functions that are not related to your needs.


Contact Us


Get In Touch or Get A Quote

Need an expert? you are more than welcomed to
leave your contact info and we will be in touch shortly
YOUR COMPANY
Sifangyuan Industrial Park, Xinshapu, Huaide Community
Humen town, Dongguan City, Guangdong Province. 
860769-82886112
860769-82886112